102 lines
4.3 KiB
TOML
102 lines
4.3 KiB
TOML
|
[manager]
|
||
|
|
monitor_udev = true
|
||
|
|
need_libusb = true
|
||
|
|
usb_vid = 0x2c7c
|
||
|
|
usb_pid = 0x0125
|
||
|
|
|
||
|
|
# Delay between setting GPIO and PWRKEY sequence, set in microseconds
|
||
|
|
poweron_delay = 100000
|
||
|
|
|
||
|
|
# Uncomment the following if you need to change the modem detection timeout on
|
||
|
|
# resume and/or the time during which suspend is blocked after modem boot
|
||
|
|
#[suspend]
|
||
|
|
#boot_timeout = 120
|
||
|
|
#recovery_timeout = 9
|
||
|
|
|
||
|
|
[gpio]
|
||
|
|
chips = [ "1c20800.pinctrl", "1f02c00.pinctrl" ]
|
||
|
|
dtr = { chip = 1, line = 6 }
|
||
|
|
pwrkey = { chip = 0, line = 35 }
|
||
|
|
reset = { chip = 0, line = 68 }
|
||
|
|
apready = { chip = 0, line = 231 }
|
||
|
|
disable = { chip = 0, line = 232 }
|
||
|
|
|
||
|
|
[at]
|
||
|
|
uart = "/dev/ttyS2"
|
||
|
|
configure = [
|
||
|
|
# Each command has 4 possible elements:
|
||
|
|
# * `cmd` : the AT command itself, which will be translated to "AT+`cmd`"
|
||
|
|
# * `subcmd`: the subcommand in case a single AT command can be used
|
||
|
|
# to change multiple parameters, such as QCFG (optional)
|
||
|
|
# * `value` : the commands, argument, usually used to set the value of
|
||
|
|
# a specific parameter (optional)
|
||
|
|
# * `expect`: the expected return value; the command is first executed
|
||
|
|
# without any value in order to query the current state. This
|
||
|
|
# state is then compared to the `expect` string; if they don't
|
||
|
|
# match, the command is then executed with value `expect` in
|
||
|
|
# order to set the parameter to the configured value (optional)
|
||
|
|
# A command can have `expect` OR `value` configured, but it shouldn't have both
|
||
|
|
# Print software version
|
||
|
|
{ cmd = "QGMR" },
|
||
|
|
# Configure audio
|
||
|
|
{ cmd = "QDAI", expect = "1,1,0,1,0,0,1,1" },
|
||
|
|
# RI signaling using physical RI pin
|
||
|
|
{ cmd = "QCFG", subcmd = "risignaltype", expect = "\"physical\"" },
|
||
|
|
# Enable VoLTE support
|
||
|
|
{ cmd = "QCFG", subcmd = "ims", expect = "1" },
|
||
|
|
# Disable APREADY for PP 1.0 because pin is not connected
|
||
|
|
{ cmd = "QCFG", subcmd = "apready", expect = "0,0,500" },
|
||
|
|
# URC configuration for PP 1.0 (APREADY pin not connected):
|
||
|
|
# * RING URC: extend pulse length
|
||
|
|
# * Incoming SMS URC: extend pulse length
|
||
|
|
# * Other URC: extend pulse length
|
||
|
|
# * Report URCs on all ports (serial and USB) for FOSS firmware
|
||
|
|
# * Delay reporting of URCs
|
||
|
|
# * Configure URC pin to UART Ring Indicator
|
||
|
|
{ cmd = "QCFG", subcmd = "urc/ri/ring", expect = "\"pulse\",2000,1000,5000,\"off\",1" },
|
||
|
|
{ cmd = "QCFG", subcmd = "urc/ri/smsincoming", expect = "\"pulse\",2000,1" },
|
||
|
|
{ cmd = "QCFG", subcmd = "urc/ri/other", expect = "\"off\",1,1" },
|
||
|
|
{ cmd = "QCFG", subcmd = "urc/delay", expect = "1" },
|
||
|
|
{ cmd = "QCFG", subcmd = "urc/cache", expect = "0" },
|
||
|
|
{ cmd = "QCFG", subcmd = "urc/ri/pin", expect = "uart_ri" },
|
||
|
|
{ cmd = "QURCCFG", subcmd = "urcport", expect = "\"all\"" },
|
||
|
|
# Allow sleeping for power saving
|
||
|
|
{ cmd = "QSCLK", value = "1" },
|
||
|
|
# GNSS configuration:
|
||
|
|
# * Enable A-GPS data upload support (XTRA)
|
||
|
|
# * Disable On-Demand-Positioning (ODP) mode
|
||
|
|
# to avoid running the GNSS system in the background, even when not enabled.
|
||
|
|
# * Enable Dynamic Power Optimizations (DPO) mode to turn off GNSS RF radios
|
||
|
|
# when they are not in use.
|
||
|
|
# * Only enable GPS and GLONASS, disable other GNSS systems.
|
||
|
|
# A-GPS data upload doesn't work for Galileo anyway.
|
||
|
|
# * Avoid turning on GNSS support automatically when the modem boots.
|
||
|
|
{ cmd = "QGPSXTRA", expect = "1" },
|
||
|
|
{ cmd = "QGPSCFG", subcmd = "gnssconfig", expect = "4" },
|
||
|
|
{ cmd = "QGPSCFG", subcmd = "odpcontrol", expect = "0" },
|
||
|
|
{ cmd = "QGPSCFG", subcmd = "dpoenable", expect = "1" },
|
||
|
|
{ cmd = "QGPSCFG", subcmd = "gpsnmeatype", expect = "31" },
|
||
|
|
{ cmd = "QGPSCFG", subcmd = "glonassnmeatype", expect = "7" },
|
||
|
|
{ cmd = "QGPSCFG", subcmd = "galileonmeatype", expect = "0" },
|
||
|
|
{ cmd = "QGPSCFG", subcmd = "beidounmeatype", expect = "0" },
|
||
|
|
{ cmd = "QGPSCFG", subcmd = "autogps", expect = "0" },
|
||
|
|
# Disable fast poweroff for stability
|
||
|
|
{ cmd = "QCFG", subcmd = "fast/poweroff", expect = "0" },
|
||
|
|
# Configure sleep and wake up pin levels to active low
|
||
|
|
{ cmd = "QCFG", subcmd = "sleepind/level", expect = "0" },
|
||
|
|
{ cmd = "QCFG", subcmd = "wakeupin/level", expect = "0,0" },
|
||
|
|
# Do not enter RAMDUMP mode, auto-reset instead
|
||
|
|
{ cmd = "QCFG", subcmd = "ApRstLevel", expect = "1" },
|
||
|
|
{ cmd = "QCFG", subcmd = "ModemRstLevel", expect = "1" },
|
||
|
|
]
|
||
|
|
suspend = [
|
||
|
|
]
|
||
|
|
resume = [
|
||
|
|
]
|
||
|
|
reset = [ { cmd = "CFUN", value = "1,1" } ]
|
||
|
|
|
||
|
|
[gnss]
|
||
|
|
enabled = true
|
||
|
|
url = "https://xtrapath4.izatcloud.net"
|
||
|
|
file = "xtra2.bin"
|