Added extra

dev-embedded/u-boot-pinephone-pro/files/boot.txt

@@ -1,37 +0,0 @@
-#
-# /boot/boot.txt
-# After modifying, run "ppp-uboot-mkscr" to re-generate the U-Boot boot script.
-#
-
-#
-# This is the description of the GPIO lines used in this boot script:
-#
-# GPIO #105 is GPIO3_B1, or RK3399 ball C27, which controls the vibrator motor
-# GPIO #154 is GPIO4_D2, or RK3399 ball AH3, which controls the red part of the multicolor LED
-# GPIO #157 is GPIO4_D5, or RK3399 ball AJ3, which controls the green part of the multicolor LED
-# GPIO #158 is GPIO4_D6, or RK3399 ball AG4, which controls the blue part of the multicolor LED
-#
-
-gpio set 105
-gpio set 154
-
-# Set root partition to the second partition of boot device
-part uuid ${devtype} ${devnum}:1 uuid_boot
-part uuid ${devtype} ${devnum}:2 uuid_root
-
-setenv bootargs loglevel=4 console=tty0 console=${console} earlycon=uart8250,mmio32,0xff1a0000 consoleblank=0 boot=PARTUUID=${uuid_boot} root=PARTUUID=${uuid_root} rw rootwait quiet audit=0
-
-if load ${devtype} ${devnum}:${distro_bootpart} ${kernel_addr_r} /Image; then
-  gpio clear 105
-  if load ${devtype} ${devnum}:${distro_bootpart} ${fdt_addr_r} /dtbs/${fdtfile}; then
-    if load ${devtype} ${devnum}:${distro_bootpart} ${ramdisk_addr_r} /initramfs-linux.img; then
-      gpio set 157
-      booti ${kernel_addr_r} ${ramdisk_addr_r}:${filesize} ${fdt_addr_r};
-    else
-      gpio set 158
-      booti ${kernel_addr_r} - ${fdt_addr_r};
-    fi;
-  fi;
-fi
-
-# EOF

dev-embedded/u-boot-pinephone-pro/files/ppp-uboot-flash

@@ -1,60 +0,0 @@
-#!/bin/bash
-
-#
-# /usr/bin/ppp-uboot-flash
-# Utility that flashes selected U-Boot image to the boot device.
-#
-
-# Check that we're running as root
-if [[ ${EUID} != 0 ]]; then
-  echo "Flashing U-Boot image not possible, please execute this utility as root."
-  exit 1
-fi
-
-# Get the device that the root resides on, and remove "/dev/" from the device name
-ROOT_DEV=`findmnt / -o source -n | cut -d "[" -f 1 | cut -d "/" -f 3`
-
-# Get the full real name of the root device, which is usually "/dev/mmcblk0"
-ROOT_DEV_NAME="/dev/"`echo /sys/block/*/${ROOT_DEV} | cut -d "/" -f 4`
-
-# Verify that the determined root device is available, just in case
-if [[ ! -r ${ROOT_DEV_NAME} ]]; then
-  echo "Flashing U-Boot not possible, device ${ROOT_DEV_NAME} not found.  No changes made to U-Boot."
-  exit 1
-fi
-
-# Get the U-Boot component names and check that they exist
-IDBLOADER_IMG="/boot/idbloader.img"
-U_BOOT_ITB="/boot/u-boot.itb"
-for COMPONENT in ${IDBLOADER_IMG} ${U_BOOT_ITB}; do
-  if [[ ! -r ${COMPONENT} ]]; then
-    echo "Flashing U-Boot not possible, file ${COMPONENT} not found.  No changes made to U-Boot."
-    exit 1
-  fi
-done
-
-# Flash the first of the selected U-Boot components to the determined root device
-echo -n "Flashing U-Boot components..."
-dd if=${IDBLOADER_IMG} of=${ROOT_DEV_NAME} seek=64 conv=notrunc,fsync > /dev/null 2>&1
-STATUS_IMG=$?
-STATUS_ITB=0
-
-# Now flash the second U-Boot component, but only if the first one flashed successfully
-if [[ ${STATUS_IMG} = 0 ]]; then
-  dd if=${U_BOOT_ITB} of=${ROOT_DEV_NAME} seek=16384 conv=notrunc,fsync > /dev/null 2>&1
-  STATUS_ITB=$?
-fi
-
-# At the end, display the final status message of the U-Boot flashing
-if [[ ${STATUS_IMG} = 0 && ${STATUS_ITB} = 0 ]]; then
-  echo " done."
-  echo "Required U-Boot components flashed to ${ROOT_DEV_NAME} successfully."
-  echo "Please reboot your phone for the changes to take effect."
-else
-  echo " failed."
-  echo "Flashing U-Boot components to ${ROOT_DEV_NAME} failed due to unknown reason."
-  echo "Please try flashing the U-Boot again, or your phone may no longer boot properly."
-  exit 1
-fi
-
-# EOF

dev-embedded/u-boot-pinephone-pro/files/ppp-uboot-mkscr

@@ -1,68 +0,0 @@
-#!/bin/bash
-
-#
-# /usr/bin/ppp-uboot-mkscr
-# Utility that generates the U-Boot boot script.
-#
-
-# Source and destination file paths
-BOOT_TXT="/boot/boot.txt"
-BOOT_SCR="/boot/boot.scr"
-
-# Boot script description
-IMAGE_DESC="U-Boot boot script"
-
-# Determine the performed action
-if [[ ! -r ${BOOT_SCR} ]]; then
-  ACTION="Generating"
-else
-  ACTION="Re-generating"
-fi
-
-# Check that we're running as root
-if [[ ${EUID} != 0 ]]; then
-  echo "${ACTION} ${IMAGE_DESC} not possible, please execute this utility as root."
-  exit 1
-fi
-
-# Make sure that the required utility is available
-if [[ ! -x /usr/bin/mkimage ]]; then
-  echo "${ACTION} ${IMAGE_DESC} not possible, mkimage utility not found."
-  echo "Please install the uboot-tools package, by running the following command:"
-  echo "  emerge dev-embedded/uboot-pinephone-pro"
-  exit 1
-fi
-
-# Check that the source file exists
-if [[ ! -r ${BOOT_TXT} ]]; then
-  echo "${ACTION} ${IMAGE_DESC} not possible, file ${BOOT_TXT} not found."
-  echo "Please reinstall the uboot-pinephone package, by running the following command:"
-  echo "  emerge dev-embedded/uboot-pinephone-pro"
-  exit 1
-fi
-
-# Is this a quiet execution?
-VERBOSE=true
-while getopts "q" SWITCH; do
-  if [[ ${SWITCH} = "q" ]]; then
-    VERBOSE=false
-  fi
-done
-
-# Generate the U-Boot boot script
-echo -n "${ACTION} ${IMAGE_DESC} ${BOOT_SCR}..."
-if [[ ${VERBOSE} = true ]]; then
-  echo
-  mkimage -A arm -O linux -T script -C none -n "${IMAGE_DESC}" -d ${BOOT_TXT} ${BOOT_SCR}
-else
-  mkimage -A arm -O linux -T script -C none -n "${IMAGE_DESC}" -d ${BOOT_TXT} ${BOOT_SCR} > /dev/null 2>&1
-  if [[ $? = 0 ]]; then
-    echo " done."
-  else
-    echo " failed."
-    echo "${ACTION} ${IMAGE_DESC} from ${BOOT_TXT} failed due to unknown reason."
-    echo "Please try generating the boot script again, or your phone may no longer boot properly."
-  fi
-fi
-
-# EOF